$250M SERIES B • $1.5B VALUATION • Physics is ready for its next era
Schedule a Demo
Back to all blogs

Product Updates

How Much Better Could Your Product Be If You Could Accurately Simulate 1 Million Thermal Design Alternatives in a Day?

11.6.2026 | By Manav

Most of the design space never gets simulated

Every physical design decision in a phone, tablet or wearable creates a thermal tradeoff. Take 100 microns out of the stack. Give the processor another watt. Increase battery capacity. Move the camera 2 mm. Replace one interface material with another. Shave a fraction of a gram from a bracket. Each change affects how heat moves through the product, and each one interacts with dozens of other choices. Engineers have no shortage of alternatives worth exploring. Conventional thermal analysis forces them to choose the few they have time to simulate.

Those alternatives multiply quickly. Six design choices with five options each make 15,625 combinations, before power levels or use cases are added. A team that can run a few thermal studies per design cycle sees a fraction of a percent of that space and fills the rest with assumptions and margin. When a full-detail simulation takes seconds to set up and minutes to run, teams can test all of those thousands of combinations instead of guessing which ones matter, and challenge the assumptions they would otherwise carry forward.


Every design choice is a thermal tradeoff

Pick up a phone after a long video call and you can feel where its processor sits. There is no fan inside and no room for one. Every watt the chips produce has to travel through solid material (a graphite sheet, an EMI Shield, an aluminum frame, the glass) before it reaches your hand and the air around it.

In a sealed, fanless device, heat leaves the chip in two directions: down through the package into the board, and up through a shield, heat pipe or spreader toward the display and back cover. From there it spreads sideways through metal and graphite until the outer surfaces can shed it.

Three limits shape every design decision along that path:

  • Junction temperature. Each chip has a maximum it must stay under, or it throttles and the user notices.
  • Human factors. The outer surface has to stay comfortable to hold, which in a thin device is often the tighter limit.
  • Space. Every 100 microns spent on a heat spreader comes from the battery, the camera or the display stack.

Because conduction carries the heat through the product, the details of that path matter: how thick the spreader is, where the shield touches the frame, which thermal interface material sits between the chip and the heat spreader. Those are exactly the details that tend to get simplified away in a thermal model. They are also choices that interact. A spreader thickness that works with one battery may not work once the battery grows or the processor gets another watt.


Why today's workflow tests only a few designs

A device’s mechanical CAD is detailed: hundreds to thousands of bodies, including screws, clips, and solder joints. Most thermal tools can’t solve that directly, so a typical study looks like this:

  1. The mechanical team exports the assembly.
  2. A thermal analyst spends hours to days to remove small features, repair broken geometry and convert parts into the tool’s simplified objects.
  3. Boards get an averaged conductivity, and chips become boxes with a power value.
  4. The analyst tunes the mesh, runs the solve, and reports back days later.
  5. The design has moved on, so the loop starts again from scratch.

Each pass takes days, so a team can afford only a handful of studies per design cycle. Someone has to decide which variants are worth simulating before anyone knows the answers, and the rest of the design space goes unchecked. Choices carried over from the last product, such as the spreader thickness, the interface material or the battery position, rarely get tested again, and teams add margin to cover what they couldn’t check. The simplifications in steps 2 and 3 can also hide the local detail that causes a hotspot, so a problem may only show up on a physical prototype, when there is only time to mitigate it.


What changes when a simulation takes minutes

To explore the design space instead of sampling it, a team needs three things at once. Vinci brings them together on one platform:

  • Full native geometry. Vinci solves the STEP assembly as the mechanical team built it, every body included, so a CAD revision is a new run rather than a new modeling project.
  • Speed. Solves run on GPUs in minutes, and a design of experiments can sweep many variants in one batch.
  • Detail that holds up. Small features stay in the model, so the hotspots they cause show up in the results instead of being averaged away.

With all three in place, the work changes. Teams can test combinations of choices rather than the few that looked most promising, rerun the whole set after each CAD revision, and find interactions that a one-change-at-a-time study misses. Assumptions inherited from the last product get checked instead of carried forward, and the tradeoffs between thermal margin, battery capacity, thickness and performance get decided with data while the design can still change.


The workflow in Vinci

Vinci reads the STEP assembly as it is and solves it on GPUs. Instead of converting each part into a simplified object, it fills the assembly with voxels, so detail stays in the model.

  1. Import the assembly. Upload the STEP file from the mechanical team. Vinci reads every body and the assembly hierarchy, so the model matches what the designers see in CAD.
  2. Assign materials in one file. A single CSV maps materials to components or whole sub-assemblies: aluminum for the heat shield, graphite for the spreader, aluminium for the frame. The same file works again on the next CAD revision.
  3. Add power where it is made. Give each chip its wattage. For a processor with known hotspots, apply a 2D power map to its surface, in true detail. For a vendor part with no internal detail, use the two thermal resistances from its datasheet.
  4. Set the surroundings. Apply the conditions at the outer surfaces, such as a heat-transfer coefficient to room air, to represent how the device sheds heat.
  5. Solve and inspect. Read off minimum, maximum and average temperature for every component, and slice through the device with clipping planes to see where heat is transferring.

Questions you can answer before the design is locked

With the full assembly solving in minutes, thermal analysis can keep pace with mechanical changes and cover far more of the design space:

  • Does moving the battery 2 mm change the processor’s junction temperature?
  • Is a thicker graphite sheet worth the space, or does a different interface material do more?
  • Which component runs closest to its limit at peak load, and how much margin is left?
  • After the latest CAD revision, did any hotspot move under the user’s hand?
  • Across every combination of spreader thickness, interface material and battery position, which designs stay under touch temperature limit with the most battery capacity?
  • Is the spreader thickness carried over from the last product still the right choice for this one?

The chips inside the device may already be modeled in Vinci by your package team. With STEP support, the device around them now runs on the same platform, so chip and product thermal work no longer live in separate tools.

Conduction on STEP geometry is available now in Vinci. Talk to our team to see how many alternatives you can explore on your own device assembly.

Schedule a demo

Manav's Headshot

Manav is a product marketing leader with experience at Adobe, Cisco, Samsung, and SpaceX. At Vinci, he leads product marketing for their Physics Intelligence Platform. He holds an MBA from Duke University’s Fuqua School of Business and a B.S. in Computer Science from NC State University.